Oxidational wear of low alloy steel in gases other than air

A pin on disc wear machine has been used to study the oxidational wear of low alloy steel in a series of experiments which were carried out under dry wear sliding conditions at range of loads from 11.28 to 49.05 N and three sliding speeds of 2 m/s, 3.5 m/s and 5 m/s, in atmosphere of air, Ar, CO2, 100% O2, 20% O2-80% Ar and 2% O2-98% Ar. Also, the experiments were conducted to study frictional force, surface and contact temperatures and surface parameters of the wearing pins. The wear debris was examined using x-ray diffraction technique for the identification of compounds produced by the wear process. Scanning electron microscopy was employed to study the topographical features of worn pins and to measure the thickness of the oxide films. Microhardness tests were carried out to investigate the influence of the sub-surface microhardness in tribological conditions. Under all loads, speeds and atmospheres parabolic oxidation growth was observed on worn surfaces, although such growth is dependent on the concentration of oxygen in the atmospheres employed. These atmospheres are shown to influence wear rate and coefficient of friction with change in applied load. The nature of the atmosphere also has influence on surface and contact temperatures as determined from heat flow analysis. Unlubricated wear debris was found to be a mixture of αFe2O3, Fe3O4 and FeO oxide. A model has been proposed for tribo-oxide growth demonstrating the importance of diffusion rate and oxygen partial pressure, in the oxidation processes and thus in determination of wear rates.

An investigation of the emerging system of host government participation in the international oil industry with particular reference to Libyan participation arrangements

This study has been conceived with the primary objective of identifying and evaluating the financial aspects of the transformation in country/company relations of the international oil industry from the traditional concessionary system to the system of governmental participation in the ownership and operation of oil concessions. The emphasis of the inquiry was placed on assembling a case study of the oil exploitation arrangements of Libya. Through a comprehensive review of the literature, the sociopolitical factors surrounding the international oil business were identified and examined in an attempt to see their influence on contractual arrangements and particularly to gauge the impact of any induced contractual changes on the revenue benefit accruing to the host country from its oil operations. Some comparative analyses were made in the study to examine the viability of the Libyan participation deals both as an investment proposal and as a system of conducting oil activities in the country. The analysis was carried out in the light of specific hypotheses to assess the relative impact of the participation scheme in comparison with the alternative concessionary model on the net revenue resulting to the government from oil operations and the relative effect on the level of research and development within the industry. A discounted cash flow analysis was conducted to measure inputs and outputs of the comparative models and judge their revenue benefits. Then an empirical analysis was carried out to detect any significant behavioural changes in the exploration and development effort associated with the different oil exploitation systems. Results of the investigation of revenues support the argument that the mere introduction of the participation system has not resulted in a significant revenue benefit to the host government. Though there has been a significant increase in government revenue, associated with the period following the emergence of the participation agreements, this increase was mainly due to socio-economic factors other than the participation scheme. At the same time the empirical results have shown an association of the participation scheme with a decline of the oil industry's research and development efforts.

Cost effectiveness of production control systems

This thesis deals with the problems associated with the planning and control of production, with particular reference to a small aluminium die casting company. The main problem areas were identified as: (a) A need to be able to forecast the customers demands upon the company's facilities. (b) A need to produce a manufacturing programme in which the output of the foundry (or die casting section) was balanced with the available capacity in the machine shop. (c) The need to ensure that the resultant system enabled the company's operating budget to have a reasonable chance of being achieved. At the commencement of the research work the major customers were members of the automobile industry and had their own system of forecasting, from which they issued manufacturing schedules to their component suppliers, The errors in the forecast were analysed and the distributions noted. Using these distributions the customer's forecast was capable of being modified to enable his final demand to be met with a known degree of confidence. Before a manufacturing programme could be developed the actual manufacturing system had to be reviewed and it was found that as with many small companies there was a remarkable lack of formal control and written data. Relevant data with regards to the component and the manufacturing process had therefore to be collected and analysed. The foundry process was fixed but the secondary machining operations were analysed by a technique similar to Component Flow Analysis and as a result the machines were arranged in a series of flow lines. A system of manual production control was proposed and for comparison, a local computer bureau was approached and a system proposed incorporating the production of additional management information. These systems are compared and the relative merits discussed and a proposal made for implementation.